Wu Yue,Li Zhuo,Lu RongFirst published: 26 February 2020 https://doi.org/10.1002/prep.201900411Citations: 3
Abstract
Using an improved Carreau constitutive model, a numerical simulation of the casting process of a type of solid propellant slurry vacuum plate casting was carried out using the Flow3D software. Through the flow process in the orifice flow channel and the combustion chamber, the flow velocity of the slurry passing through the plate flow channel was quantitatively analyzed, and the viscosity, shear rate, and leveling characteristics of the slurry in the combustion chamber were qualitatively analyzed and predicted. The pouring time, pouring quality, and flow state predicted by the numerical simulation were verified using a visual tester consisting of a vacuum plate casting system in which a pouring experiment was carried out. Studies have shown that HTPB three-component propellant slurry is a typical yielding pseudoplastic fluid. When the slurry flows through the flower plate and the airfoil, the fluid shear rate reaches its maximum value and the viscosity of the slurry decreases. The visual pouring platform was built and the experiment was controlled according to the numerically-calculated parameters, ensuring the same casting speed. The comparison between the predicted casting quality and the one obtained in the verification test resulted in an error less than 10 %. Moreover, the error between the simulated casting completion time and the process verification test result was also no more than 10 %. Last, the flow state of the slurry during the simulation was consistent with the one during the experimental test. The overall leveling of the slurry in the combustion chamber was adequate and no relatively large holes and flaws developed during the pouring process.
개선된 Carreau 구성 모델을 사용하여 FLOW-3D 소프트웨어를 사용하여 고체 추진제 슬러리 진공판 유형의 Casting Process에 대한 수치 시뮬레이션을 수행했습니다. 오리피스 유로와 연소실에서의 유동과정을 통해 판 유로를 통과하는 슬러리의 유속을 정량적으로 분석하고, 연소실에서 슬러리의 점도, 전단율, 레벨링 특성을 정성적으로 분석하하고, 예측하였습니다.
타설시간, 타설품질, 수치해석으로 예측된 유동상태는 타설실험을 수행한 진공판주조시스템으로 구성된 비주얼 테스터를 이용하여 검증하였습니다.
연구에 따르면 HTPB 3성분 추진제 슬러리는 전형적인 생성 가소성 유체입니다. 슬러리가 플라워 플레이트와 에어포일을 통과할 때 유체 전단율이 최대값에 도달하고 슬러리의 점도가 감소합니다.
시각적 주입 플랫폼이 구축되었고 동일한 주조 속도를 보장하기 위해 수치적으로 계산된 매개변수에 따라 실험이 제어되었습니다. 예측된 casting 품질과 검증 테스트에서 얻은 품질을 비교한 결과 10 % 미만의 오류가 발생했습니다.
또한 모의 casting 완료시간과 공정검증시험 결과의 오차도 10 % 이하로 나타났습니다.
마지막으로 시뮬레이션 중 슬러리의 흐름 상태는 실험 테스트 시와 일치하였다. 연소실에서 슬러리의 전체 레벨링은 적절했으며 주입 과정에서 상대적으로 큰 구멍과 결함이 발생하지 않았습니다.
References
[1] B. M. Bandgar, V. N. Krishnamurthy, T. Mukundan, K. C. Sharma,
Mathematical Modeling of Rheological Properties of HydroxylTerminated Polybutadiene Binder and Dioctyl Adipate Plasticizer, J. Appl. Polym. Sci. 2002, 85, 1002–1007.
[2] B. Thiyyarkandy, M. Jain, G. S. Dombe, M. Mehilal, P. P. Singh, B.
Bhattacharya, Numerical Studies on Flow Behavior of Composite Propellant Slurry during Vacuum Casting, J.Aerosp.Technol.
Manage. 2012, 4, 197–203.
[3] T. Shimada, H. Habu, Y. Seike, S. Ooya, H. Miyachi, M. Ishikawa,
X-Ray Visualization Measurement of Slurry Flow in Solid Propellant Casting, Flow Meas. Instrum. 2007, 18, 235–240.
[4] Y. Damianou, G. C. Georgiou, On Poiseuille Flows of a Bingham
Plastic with Pressure-Dependent Rheological Parameters, J.
Non-Newtonian Fluid Mech. 2017, 250, 1–7.
[5] S. Sadasivan, S. K. Arumugam, M. Aggarwal, Numerical Simulation of Diffuser of a Gas Turbine using the Actuator Disc
Model, J.Appl. Fluid Mech. 2019, 12, 77–84.
[6] M. Acosta, V. L. Wiesner, C. J. Martinez, R. W. Trice, J. P. Youngblood, Effect of Polyvinylpyrrolidone Additions on the Rheology of Aqueous, Highly Loaded Alumina Suspensions, J. Am.
Ceram. Soc. 2013, 96, 1372–1382.
[7] Y. Wu, Numerical Simulation and Experiment Study of Flower
Plate Pouring System for Solid Propellant, Chin. J. Expl. Propell.
2017, 41, 506–511.
[8] T. M. G. Chu, J. W. Halloran, High-Temperature Flow Behavior
of Ceramic Suspensions, J. Am. Ceram. Soc. 2004, 83, 2189–
2195.
[9] T. Kaully, A. Siegmann, D. Shacham, Rheology of Highly Filled
Natural CaCO3 Composites. I. Effects of Solid Loading and Particle Size Distribution on Capillary Rheometry, Polym. Compos.
2007, 28, 512–523.
[10] M. M. Rueda, M.-C. Auscher, R. Fulchiron, T. Périé, G. Martin, P.
Sonntag, P. Cassagnau, Rheology and Applications of Highly
Filled Polymers: A Review of Current Understanding, Prog. Polym. Sci. 2017, 66, 22–53.
[11] F. Soltani, Ü. Yilmazer, Slip Velocity and Slip Layer Thickness in
Flow of Concentrated Suspensions, J. Appl. Polym. Sci. 1998,
70, 515–522.
[12] E. Landsem, T. L. Jensen, F. K. Hansen. E. Unneberg, T. E. Kristensen, Neutral Polymeric Bonding Agents (NPBA) and Their
Use in Smokeless Composite Rocket Propellants Based on
HMX-GAP-BuNENA. Propellants, Explos., Pyrotech.. 2012, 37,
581–589.
[13] J. Mewis, N. J. Wagner, Colloidal Suspension Rheology, Cambridge University Press, 2011.
[14] D. M. Kalyon, An Overview of the Rheological Behavior and
Characterization of Energetic Formulations: Ramifications on
Safety and Product Quality, J. Energ. Mater. 2006, 24, 213–245.
[15] H. Ohshima, Effective Viscosity of a Concentrated Suspension
of Uncharged Spherical Soft Particles, Langmuir 2010, 26,
6287–6294.